This automatic optical fiber tensile testing system is made for operator skill impartial use in production and lab settings. Two basic design configurations allow the user to select between a set up for standard linear proof testing along with extra mandrels for rotary high strength testing.

The linear edition is designed for creation evidence testing with causes approximately 22 N. Motor-driven clamps with carefully developed rubberized inserts be sure that the Sheathing Line is not really damaged in the screening process while simultaneously getting rid of the requirement for an outside air supply. Amounts of pulling force, tugging speed and hold time are automated and conveniently offered to the operator through the built-in LCD touchscreen display manage. Information from assessments can be saved and accessed using the USB dock or Ethernet user interface.

Mandrels of the same design as in NYFORS’ optical fiber recoaters can be easily mounted on the evidence tester in the rotary high power configuration. The fiber is wrapped across the two mandrels which support it with a unique clamping system. This way higher lots can be applied to the fiber, allowing breaking up strength tests under managed circumstances.

Adjustable clamp positioning facilitates screening with the highest force levels as well as screening of brief fiber measures. The lightweight and light weight design helps make the instrument easy to maneuver in a lab atmosphere and also to incorporate in a production work bench in which space is at reduced. The device is really a compact and light-weight instrument suitable for screening the effectiveness of optical materials up to 30 N. The equipment is designed to fulfill all sorts of programs when a power test has to be performed.

The equipment is made with all the consumer in mind. The FTTH Cable Production Line is easily put into the carefully guided linear clamps, as well as the testing begins instantly using a “One Touch” go button. The built in microprocessor regulates all of the essential guidelines including pulling force, tugging velocity and hold time. This enables for any completely controlled test every time.

The equipment can be attached to another PC, which enables access to all automated parameters and settings. The equipment is tailored to face-on your own use or even to the integration into different subsystems. The device has an substantial capability of signing and conserving information like tugging force, tugging velocity and fiber diameter and other parameters.

Two recoat injector configurations can be purchased. The PTR307 utilizes a computerized pump to inject the recoat materials. The volume of material dispensed by the automatic injector is controlled by hand via the top-mounted “Inject” button or programmed to the device utilizing the tablet control. The PTR307B includes a manual recoat injection system that will require an individual to personally distribute the recoat materials into the mold cavity; another one injector for that PTR307B recoater can be obtained listed below. Please note the automated injector is only suitable for higher-directory recoat materials, while the handbook injector works with both low- and high- directory recoat materials; both are sold individually below. Make sure you get in touch with Technology Assistance for more information.

he manual injector can be installed to suitable Fiber Drawing Machine via the 4-40 screws on the recoater housing (see picture towards the right). Use a 3/32″ hex key to secure the injector prior to use. To connect the PTRRRM towards the recoater mold, tighten up the connector at the end of the green plastic material tubes, then release by a 1/4 consider enable rotation.

The injector is equipped with a syndication valve and 2-position choice handle for directing the stream of recoat materials. A knurled dispensing screw having an inner plunger acts as a syringe for that recoat materials. To fill the syringe, point the handle downwards (i.e., toward the recoat container), then spin the knurled dispensing attach counterclockwise until it spins easily to fill up the syringe (demonstrated inside the photo to the right). Then, to inject the recoat material into the mold, point the handle horizontally (i.e., facing the knurled attach) and rotate the screw clockwise until nearby the finish from the journey range is achieved. Steer clear of bottoming out iuwekk dispenser because this may harm the interior plunger; also take care when re-interesting the threads in order to avoid go across threading the dispensing attach. A number of fill up/inject actions may be required till air is displaced inside the system. Use camera lens cells as well as an acetone or alcohol cleaning solution to accumulate any excess recoat materials that runs from your mold.

Sheathing Line – Want More Info..

We are using cookies on our website

Please confirm, if you accept our tracking cookies. You can also decline the tracking, so you can continue to visit our website without any data sent to third party services.